Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi
I'm trying to add CMSIS DSP Software Library to my project.
After adding DSP function I'm getting linking error:
components/toolchain/cmsis/dsp/GCC/libarm_cortexM4lf_math...
Hi all,
I have a problem with 802.15.4 association in beaconned PAN. Basically I have two devices, PAN coordinator and an FFD. FFD is able to find the coordinator (throught...
Hi. I am working on the nRF52840 DK. Currently, I am trying to implement a DFU feature for my application.
The application has the bonding feature. Therefore, I tried testing...
Hi.
I purchased a nordic thingy 91 in Singapore. But when i try to update firmware through programmer, it is not detecting the module. Also i am not able to activate the...
Hi,
I'm using a custom board with nrf52840 and sdk 15.1.0.
I have altered the ble central and peripheral example(ble_app_hrs_rscs_relay) to support nus central and peripheral...
Hi,
I'm using the PCA10040 devkit and pc-ble-driver s132 v5.0 to act as a central to connect to three bluetooth peripherals I have. I've made no edits to the connectivity...
Hey guys. Is there any way we can change scan parameters at runtime. I want to update parameters from another device using uart, and when I tried to make scan interval and...
HI,
I want to develop a program to access Accelerometer and gyroscope value from BMI160 sensor. I have used this BMI160 library
I alter the TWI_SENSOR code and it works...
Hi,
When I build the zephyr/samples/hello_world program for the nrf5340dk_nrf5340_cpuapp target it works as expected, but with the nrf5340dk_nrf5340_cpuappns target I...
IDE: SEGGER Embedded Studio for ARM 5.32 SDK: nRF5 SDK 15.0.0 and nRF5 SDK for Mesh 2.1.1 demo: examples\sdk_coexist\ble_app_uart_coexist\pca10040\s132\ses\client_pca10040_s132...
I am using NRF52 DK board and removed SB9 track to connect my ammeter for current measurement . I have taken ble_app_blinky ( peripheral example ) from SDK15.3.0 .
My application...
hi,all
I'm using nRF52833, s140.. pca10100.
I want to read my pcb's touch gpio..
If I touch it, it falls down to low. ( I checked it with scope..)
When viewed through...
I'm testing USB audio demo. I changed bit resolution of APP_USBD_AUDIO_FORMAT_DESCRIPTOR 16 to 24 but the widows10's USB audio device is still 16 bit. how can i do that?
