This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
currently we are developing a firmware for 52840 based on the nRF5 v.16 SDK with Softdevice 7.0.1 on a custom board. We are able to connect and bond up to 5 devices...
Hey all,
I have a custom board running nRF52832 with Softdevice S132 v6.1.0 and SDK15.2. My application requires me to start advertising without any manufacturer data...
Hi
in our device, HFXO is running permanently. There is an external LFXO running permanently as well.
Now I'm wondering what would be the additional current draw if we...
Hi community !
I create a model to send a string over mesh and it's working well ! The only thing which is strange is when my string is 9 bytes long (or under), the message...
Hi,
I currently need a 2.4Ghz OOK tx and I'm looking into the NRF52840 DK. I know it is not supported but I'm thinking of doing bitbang and control the PA to do an OOK...
Here are some question about SIG qualification:
Suppose I current use nRF52832 and S132 v7.0.1 ( QDID- 138862 ) and get SIG qualification without required test with Declaration...
I'm using nrf52832 with st25r3911b to let device read & write NFC card.
I modified nRF5SDK160098a08e2\examples\ble_central\ble_app_uart_c\pca10040\s132\ses to do this. ...
Hi, there,
I have a question about HFXO load capacitors and LFXO load capacitors.
Each load capacitors of nRF52840-DK are like below.
And i checked BOM file to find...
Hello! I'm somewhat new to SES and still trying to understand the program a bit. Some of the features are a bit less intuitive than others.
Right now, I'm actually not having...
Hi
From this article, It appears that up to 20 connections are possible when using S140 SDK 15.3.0 SDK on an nRF52840:
https://devzone.nordicsemi.com/f/nordic-q-a/33095...
Hi,
I am using nRF52840 with SDK 15.3.0 and S140.
I am connecting to multiple peripherals as a central device and using NUS to communicate with these peripherals. I need...
I'm trying to use the nRF5340-PDK SPIM at 16MHz, which requires me to use SPIM4 and dedicated SPIM4 pins
P0.08 - SCK for SPIM4
P0.09 - MOSI for SPIM4
P0.10 - MISO for...
Hello! I have implemented a OTA cluster basing on the example: https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/zigbee_example_ota_client.html
I use almost exactly...
Dear Amazing Community,
We are currently investigating any uA being consumed by our nrf52833.
We are using the PPK to track them and we believe that during normal operations...
I developed a custom RF mesh to USB serial bridge. Right after boot, I receive all serial messages, but once the host closes the serial port and open it again, nothing comes...
