I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
I plan to use nrf52840 in high voltage mode (connected directly to the power source via VDDH pin) with button.
And I plan to use voltage regulator with EN pin (with pull...
The most relevant thread on this topic is two years old. I do not want to use Keil as it is so costly and the project may not go anywhere. I am not interesting in using the...
Is it possible for me to easily modify the nrf52 Zigbee samples to run on 1 or more of my 5340 M33 cores, or is it a rewrite?
I can see chip support for nrf52 but no mention...
Hello,
We recently sent a design to our board assembly house for review and they indicated that the large copper area under the nRF528323-CIAA (WLCSP) may result in head...
I’m using nRF52810 on a custom board (for our own application) using SDK 15.2.0 v6.1.0 S112. Given the amount of memory this chip has (192/24 KB) is it possible to implement...
I'm using the nRF52 DevKit with nrf52832 SoC. I connected a UV Sensor through the TWI interface (PINS 26 & 27, as well VDD and GND).
However, I fear it's using a lot of...
Hello,
Till now I was using nRF52840 with nRF5_SDK_16.0.0_98a08e2 and its working fine. Now I thought to cross check with nRF52832.
When I run FDS example I am getting...
I have been studying the power consumption of a prototype and observe that the end device is polling very frequently. The data request polling is backing off for a while to...
I've been observing a strange behaviour on the MOSI line using SPI2 in Mode 0(nRF52832) with connected ST7789 based display,
The data happens to be not available at the...
Dear Nordic support team,
I am developing a prototype based on the nRF52840 with the nRF5 SDK 16.0.0 and Soft Device S140 7.0.1. The prototype acts in the peripheral role...
I'm using nrf52840 and SDK VR 15.0.0
I want to apply the long press button functionality and short press button functionality to change the screens in OLED SSD1306.
How...
I am using NRF52840 in Mesh(SDK 4.1.0).
I followed Hung Bui's solution and change power to 8 dBm in code, but get range of 15 meter in open environment, This is very low...
Dear all, I have a question about custom address add. In light switch example, we can publish message to group address or unicast address. In my project, we want to send message...
