This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hey, I am using nrf51822 nRF5_SDK_12.3.0_d7731ad SDK and using Segger embedded studio. In the application code my memory segments is this. Now I want to do firmware update...
Hello,
I am debugging my nRF52832 with JLinkRTTClient through NRF_LOG, but there seems to be some issues I don't quite understand with the color coding of the logging messages...
Hi there, we use the nRF52840 on a embedded system. The nRF52840 is connected via usb interface to the central cpu of the embedded system. An embedded linux (buildroot) is...
Hi!
Is it technically possible to implement performing of unmodulated TX carrier transmission by a write to some BLE characteristic? If yes, then from what to start?
Thank...
Hi,
I am trying to use the Bluetooth low energy capability of the nRF9160 DK (nRF52840 chip) by using the lte_ble_gateway sample from Nordic. After changing some lines of...
Hi
I'm using ZigBee light control coordinator example in "nRF5 SDK for Thread and Zigbee v3.1.0" on nRF52840 evaluation board.
when it will execute bdb_start_top_level_commissioning...
I am runing the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub. I have set the a single change on the code:
The device will be connected...
A couple questions about the nRF52840 GPIO Electrical Specification:
1. In the nRF52840 GPIO Electrical specification, VOH at 0.5mA is spec'd to go as low as VDD - 0.4V...
Hello,
I have been using the development kit for more than a month when after one flashing, the LED 5 on the board started blinking at one second intervals and the board...
I read a nRF9160 DK 0.8.5 circuit design and have a question about the GPS circuitry. What will happen if I bring the LTE antenna closer to the GPS antenna and reduce the...
Hi,
We have a program that uses the radio driver for IEEE 15.4. Currently we do not need Bluetooth and IEEE 15.4 working simultaneously but we do need Bluetooth DFU. When...
Hi,
Just spent a while debugging this and since there seems to be nothing - well I can't find it anyway - up here thought I should document this issue. This relates to SDK...
hi ...
i am using nrf toolbox (ble uart )to receive data from nrf52832 ..i am receiving the data for every one minute . i am facing the issue in auto connect see the below...
Hi,
Actually I am interested in making the custom design Board for the nRF52 series , so where can i find the schematics , layout files of the nRF52 Development Kit ....
Using s140 for the nRF52840 is it possible to have a BLE multilink connection (up to 8peripherals) with an extended MTU size (around 70bytes)?
All examples that I have seen...
