Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
I am working on RTLS project using nrf52832 SOC. In beacon mode i want to advertise temperature and battery strength . but i am not sure if what method should i use to measure...
Hi,
I am using nrf51822 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is i have imported the example program from the sdk...
The nRF52840 supports 2 Master/Slave instances.
Is it possible to configure the nRF52840 as a Master when connected to an I2C bus that has another Master present?
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm using nrf_fstorage_wrile() which work fine on most of the cases, except for len == 6 bytes. When I read back on the Flash, after successful write, I found that only 6...
Hi,
It‘s great thing that the nRF9160 DK can buy.
But there are few question need to be confirmed?
1, I saw the "Onging ceretifications" ( https://www.nordicsemi.com...
Hi,
I am using a nRF9160 with the LTE-M modem firmware. But I want to change it to the NB-IoT firmware. I have followed the instructions to install the dfu.
But when I...
Hi
I am looking at the file
\examples\light_switch\server\light_switch_server_nrf52840_xxAA_s140_6_1_0.emProject
and in there I see that there is the line
linker_section_placements_segments...
Hi,
We are planning to develop an IOT device using the nRF52840 which will communicate with a Hub device which will contain another nRF52840 chip, so we want to check the...
Hello,
I am compiling with encryption implemented for Bluetooth communications. Specifically with code taken from the ble_app_hrs_c example.
I am seeing this error:
...
Hi Sir
I am testing nRF52840 product with CMW500 BT5.0 testing script. But the testing is easily stop due to connection broken, especially for RX and long range testing...
I made an application based on ble_app_uart example using s130_nrf51_2.0.1_softdevice.hex and I have 2 boards:
- 1 nrf51DK
- 1 target board using nRF51822-QFAA H0 (version...
