Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi ,
I want to add DFU service into ble_app-uart example, for that I want take reference as ble_app_buttonless_dfu.
But when I am trying to test the working of ble_app_button_less_dfu...
I developed an application based on ble_app_uart and it is working on my nRF51 DK. I can see the ports driven by my application responding and Bluetooth communication is working...
I am currently using Mesh SDK 3.1, running on NRF52480 with SoftDevice140. We are currently modifying the light switch client, and would like to know which servers are available...
Hello,
I would like to implement a device that is part of a BLE Mesh Network and on the other side connects to another device directly with BLE Stack (1:1) and GATT.
...
I am developing an android application to get real-time temperature over BLE notification. Currently, I receive the temperature sensing data 1 time per second. Based on the...
Hello,
In nrf_dfu_ble.c BLE_GAP_EVT_SEC_PARAMS_REQUEST pairing on Windows 10, the following code:
err_code = sd_ble_gatts_value_get(m_conn_handle, BLE_UUID_GATT_CHARACTERISTIC_SERVICE_CHANGED...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
I want to implement the function of periodic temperature collection，but I didn`t find any data show in putty terminal，and I`ve set NRFX_TIMER_ENABLED 1 NRFX_TIMER0_ENABLED...
Hello,
The BLE mesh spec says the following:
Heartbeat is used to monitor nodes on a network and discover how far nodes are apart from each other.
Is there an example...
Hello. I have read a topic about ADC calibration (gain and offset error in 0x10000024) of nRF51822 here but I can't find the document describing it. Could anyone point me...
Hi,
I am beginning to design a wearable device with motor vibration using nRF52 SDK and SoftDevice S132.
In firmware side, I have no problem to control a led on and off...
Hi
in my test bench for system validation I would like to control the system based on nRF52 via Bluetooth to speed up testting of various samples.
It seems that there...
Good day.
We recently bought the NRF52 DK and the Power Profiler Kit with the intent to log power consumption of our battery powered products. Before purchasing the products...
Hi,
I tried nrf connect and nrf hrs example. I used nrf52DK. I bonded the device, and connected with autoconnect. I turned off the nrf 52 DK, and turn on. The nrf connect...
