Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I am trying to program the application into the CortexM33.
I am using the lte_cloud_demo_v0.3.5 , compiled under Keil.
using nrfjprog:
\DemoPack1_EU-1.4\Firmware...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am using the PCA10040 as a peripheral. When a connection is established...
Of course accurate power consumption isn't possible to predict. However, it would be helpful to have a couple of basic numbers so we could do some back of envelope power calculations...
Hi everybody,
I am having a problem using pwm with ble_app_uart example, let me explain, I want to control a servo motor via Bluetooth, so I use the ble_app_uart example...
Hello, I've read here https://devzone.nordicsemi.com/f/nordic-q-a/24490/nrf52-dk-changing-reset-pin-from-p0-21-to-somewhere-else that reset pin cannot be reconfigured to any...
Hi Nordic,
I am using NRF52832/NRF52840 SDK 15.0 to design products. And I found a strange problem that the connection will be terminated by iOS device when connection...
Hi,
I'm developing a BLE device which has one custom service and three characteristic, each characteristic has read/notify properties. My proglem is, when my device connects...
Hi all,
I want to make a windows application that can switch the light of the CoAP server example. The CoAP windows code is not the problem.
Question is, how this can...
LIKE one of your collegue told me i tried to this...but it doesn't work on the dongle..
Dongle: SDK15.2.0\examples\ble_peripheral\ble_app_blinky\pca10059\s140\<your favorite...
Good afternoon,
I am trying to get cell-tower information from ZTE-M/NB-IOT cell-tower information, in particular RSSI.
In addition - a constant refresh-rate, ideally...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am trying to support old phones without BLE 4.2 data length extension.
I have read https://punchthrough.com/pt-blog-post/maximizing-ble-throughput-part-2-use-larger-att...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello everyone,
I am having a problem with powering my nrf51822, I have 2 Li ion batteries to power my nrf51822 and a stepper motor, I put the batteries in series to have...
Hello,
Kindly asking for some guidance... We're working on a solution that requires us to distribute unique data sets (i.e., each nodes gets a different data block, approx...
