Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
Hi,
I am trying to implement the scan delegator in the broadcast_sink of the nRF5340 audio application.
Currently, I am adding the advertising feature in the broadcast_sink...
Hello, Our application image became too large for TF-M and we're investigating the use of PSA Protected Storage without TF-M as described in NCS 2.6.0.
When writing a new...
Hi,
I encountered a modem fault (NCS v2.5.1, mfw 1.3.4, nrf9160DK). Here's a portion of the log leading to the fault:
[24:36:01.333,312] <inf> gnss: event NRF_MODEM_GNSS_EVT_PVT...
Hello!
I am a beginner and am trying out an MQTT example on my nRF9161 DK that I recently bought in my Visual Studio Code on Windows 11. I am aware that the sample application...
Hi,
I am able to get my CA certificate working using TLS for MQTT. but im not able to get the TLS Client certificate working.
I had created a client certificate as per...
Hello, I'm following along the nRF Asset Tracker guide and I'm on the step 'Create device credentials'
Running the command
' ./cli.sh create-and-provision-device-cert...
Hello support.
A new design is looking at using nRF24L01+ to communicate wirelessly. I'm aware that this IC is no longer recommended for new designs, however, it's the one...
Hello,
I am trying to use the LTE modem serial example on a customized board that communicates an NRF9160 SICA B1 with an external STM32 microcontroller through the UART...
I am using the nRF52840 with NCS SDK v2.5.1. I tried to implement non-volatile storage in my application, and it is working on the DK board, but the code is not working on...
Hello,
I am using the DK Buttons and LEDs module to get the status of my button on the ANNA-B402C ( nRF52833 ).
I wanted to check if any debounce filter/mechanism software...
Hello,
as mentioned in the subject, I want to use single bank while CONFIG_BOOTLOADER_MCUBOOT=y. The reason is that the nRF7002 firmware is so large, it would cause an overflow...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I want to debug using the Logger module...