We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I'm trying out the Zephyr os for the NRF51.
When I try the basic BLE example they work fine!
However when I try the sensor example which uses the i2c it falls...
Hello Nordic Forum!
I'm currently trying to load my firmware into my custom nRF52832 board without success. I'm using the nRF52DK (PCA10040) and the nrfjprog tool.
I...
Hi All,, please confirm me this .. please confirm i-beacon Rx + ble peripheral is possible ... Also please suggest me a development kit for the same which can be easily solder...
Hello,
I would like to move the SDK12.2 template example project out of SDK12.2 installation directory. How can I do that using uVision5?
I tried to change all the reference...
Hi
I don't understand how to correctly flash all three parts so that the app runs on boot.
At the moment if I flash them all the nrf51 (51822) boots to the dfu bootloader...
I can see in the latest SDK 12.2 that signing of the dfu firmware files is possible.
Am I right in thinking that this signing verifies the source of the firmware files...
Hi, I have nrf51822QFAA series. I am using S110 for softdevice which takes 96KB. My current program size is Code=31908 RO-data=512 RW-data=312 ZI-data=8360. I want to know...
Hi.
I am using the new SDK 13.0.0 and nrf52 chip. I am trying to set a whitelist with
the peripheral_template example code.
I think the whitelist is already enabled in...
I have made an ADC driver that (should) scan 5 inputs into a sample buffer using EasyDMA. On the END event the 5 samples are transferred to 5 ring buffers read by the client...
I've tried to upgrade the firmware using the DFU feature of the android nrf-toolbox app, but it returns the "REading file failed" error.
this happens only with my phone...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...