This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
Hello,
I am using a nrf51422 development kit with softdevice S310 and I have a problem in whatever pin I choose as output when I use the bluetooth.
I run the example...
I tried code like
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
....
case BLE_GAP_EVT_TIMEOUT:
if (p_ble_evt->evt.gap_evt.params.timeout.src == BLE_GAP_TIMEOUT_SRC_ADVERTISEMENT...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am unable to compile this to fit into the allocated bootloader space.
Has anyone been able to compile this patched version of the signlebankdfu-ble
with nrf sdk v6 so...
I'm using API 2.1.3, and after several connections/disconnections with a peer device, I'm seeing the API never returning from a DiscoverPipes() call. It appears to be waiting...
Hi,
I'm using nrf51 BLE driver with usb dongle to create test application on PC which simulates
the peripheral.
My problem is I cannot add 128-bit UUID for custom service...
After some pstorage_update calls I start to get error 9. From nrf_error.h it is called NRF_ERROR_INVALID_LENGTH but from SDK doc it looks like pstorage_update does not have...
My question is in regards to BLE security. I have certain characteristics that I want to remain open. As they will be used to determine authentication at the application level...