Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I am trying to flash the nRF52840 SoC on the nRF52840 DK using an external J-Link debugger, without relying on the interface MCU or the onboard J-Link. My current switch...
Dear Nordic Engineers
I used NCS2.9.0 to develop a device based on nRF52840 and I would like to use UART to DFU the device based on SMP.
Now, I test SMP samples and use...
Hi,
After the latest update, the below setting allowing me to select nrfjprog as my device provider is now gone:
I am using the nRF Playground Docker container...
Hi,
I have been using NUS code to stream data between mobile and nrf5340 audio dk. is it possible to stream 256KB of data at a go? what is the maximum MTU size that i can...
I am using nrf connect sdk 2.7.0 with nrf52811.
My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0.
I want to know whether...
I have a problem with the package with nrf5 sdk, there for pca10100 examples are not there. i am trying to interface quadrature decoder with one encoder and it is not able...
Hello,I have a custom board using a Nordic nrf52823 microcontroller on it. I am using VSCode with the nrf connect SDK and the Zpehry RTOS- I want to make use Zephyr RTC to...
Is there any relevant assessment or introduction document of IC FMEA?
For example, the impact of abnormal short circuit and ordinary short circuit on chip 52832;
And...
1、I used the spi_bitbang routine to port it to the network core to run, and after the program was burned, I used an oscilloscope to measure the CLK pin waveform and there...
Hi,i I am testing the sample(ncs\v2.7.0\zephyr\samples\drivers\spi_bitbang) at a 52840DK board, with overlay setup like these:
spibb0: spibb0 {
compatible = "zephyr...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
Hi, I am trying to change the USB CDC/ACM com port name. I have read through some posts but they are very short or unanswered. It seems we can change the .inf driver file...
