But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
Hi,
does firmware or example source code exist for the PCA10000 USB dongle that implements the Bluetooth HID host?
I would like to use it as receiver for the Nordic Smart...
Hi all,
I am trying to specify a fixed port for a L2CAP connection on the nRF51822. The client is a Linux box running bluez (which has BLE support). The client software...
Hi,
Just bought the nRF51822 eval kit. Looks like it came with some great demos for iPhone (nRF_Demo_Utility, nRF_Proximity, nRF_Temp, nRF_UART), but having trouble getting...
Hi,
I upgraded to the 4.3 nRF51 last night and am suddenly having a whole slew of issues:
(1) When flashing the EK, the Segger now reports 257K of Flash (maybe it did...
Hi,
I'm looking to work with a Bluetooth LE master device. From what I read the nRF51822 should be able to function as a Master device (the dongle is configured to be a...
Hi all
I want to load the (UART_example) flash image compile with Keil by nRFgo studio,
but a program fail occur as below screenshot:
any idea?
Thanks.
I have test RTC example on both different hardware revision nRF51822 chip.
1)N51822 QFAAC0 1309AF
2)N51822 QFAAC0 1308AE
1309AF revision chip is function properly with...
I'm confused about how to assign a functional block's I/O (TWI in my case) to a particular pin on the device. Is there a worked and documented example? Is there a relevant...
I am trying to get wireless communication implemented on a robotics project I am working on. I'm using a PIC18F4550, PIC18F2550, and two Nordic nRF24L01's. I'm having trouble...
I'm attempting to have two separate evaluation boards talk to each other through the GHz Radio. I've read the docs, and they explain that I have to set the radio in either...