When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
I just upgraded my nRF Connect for VSC to 2.6.1 and now am getting these errors:
and
I saw this as well:
but I have CONFIG_DISPLAY =y in the prj.conf....
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
How can I properly set up the SWD interface for printk on a custom PCB? I have to build my project example and see the message printed on the VS Code console. My custom hardware...
Using nrf5340 as both Central and Peripheral roles and I have implemented the Basic Audio Profile based on the nrf5340 audio example. I am using nRF Connect v2.6.1.
I...
I need a bluetooth module that is capable of simultaneously streaming audio two way, ie two channels stereo out and 1 channel mic in with low latency. A friend had recommended...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
Hi,
My custom board nRF52840 works as a Peripheral, which advertises itself for connection from a Central.
The project is built based on peripheral_hr sample project....
Dear:
I can upgrade applicaiton ONLY sucessfully through DFU.
but now, i want to upgrade applicaiton+softdeivce+bootloader to deployed devices. do you have such documets...
Hi,
What is the maximum PWM frequency one can achieve on the nrf52840 with 50% duty cycle? Sample .dts and c-code in NRF Connect SDK would be appreciated!
In practice...
HI.
we're developing an application where we need to use 2 UART ports: UART: 0, 2, 3.
Before we added MCU boot in our project everything worked well but after we integrated...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
I have a thingy91 device and want to implement the following requirements.
Expectation:
NRF9160 should remain in deep sleep mode and on the button click event do the...
I am developing firmware for a BLE peripheral using ncs v2.6.1.
In addition to using the libraries introduced in nRF Connect SDK Fundamentals and BLE Fundamentals on DevAcademy...
