Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
I started debugging a device with an nRF52820 chip and found that the pinout is similar to nRF52833.
The test application was switching pin P0.15, but the ripple...
I'd like to order a debug in/out cable for the debugger (P18 & P19) on DK.
But I don't know what is the cable or the compatible sockets.
please let us know what is the...
We are using the following.
Module: BM833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: nRF5_SDK_17009\examples\ble_peripheral...
Hi,
I am a new comer and I try to customize samples/hello word projet
I am using nrf Connect v3.4.2 on Windows.
I try to perform a basic AES operation in main.c (based...
i am using nrf52840 DK. We have dedicated pins for say QSPI, UART, etc. but if I want to connect external flash memory i.e W25Q16 to the board, to which pins I should connect...
Hello Nordic team
I am working on nRF52832 dev board and I have a requirements to encrypt and decrypt data using AES-128 ECB . Could you please provide the example code...
The device was working well for around 2 weeks and was able to program it via SES, but now on connecting USB cable to the USB Connector (J2) with SW9 at VDD, no LEDs pulsate...
Hello
I am using the experimental_ble_app_uart for s110. I want to use the sd_temp_get() and convert the temperature value to a uint8_t, but if understand correctly when...
Current I used nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver/blob...
hi,
I am done with general vehicle diag code. now, i need to interface with kwp via uart in nrf9160 controller.
please, suggest some ideas.
Thanks in advance ...
I just bought nrf52840 and J-link V9.
I look at start nrf52840 blinky.
website:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0...
I want to read ADC values from AIN2 (P0.04), and AIN3 (P0.05) channels of nrf52805. I am using S112, and I have the following code found in the internet.
float readADC(uint8_t...
Hi,
I want to build up a test software to test our product.
I find out pc-ble-driver that might be conformed our requirement and follow up below link to set up environment...
Hello, everyone.
I am using sdk v17 and I am looking into timer. I used the app_timer simply, but I don't know the nrf_drv_timer because I've never seen it before. Can...
