Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi!
I am trying to test the Immediate Alert Client application example (ble_app_ias_c) from nRF5_SDK_15.0.0 on my nRF52832 based module. I want to understand how to test...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
Hello, We are using the NRF52840 and softdevice S140, PCA10056 on all examples. SDK version is 15.3. We see a problem following the secure OTA DFU protocol regarding acessing...
Hi,
I'm developing and testing the code using the PCA10040, but this board uses the NRF52382_XXAA which contains more memory and I want to use the NRF52382_XXAB. So, how...
Hello guys,
I have coin cell powered nRF52832 based sensor node. I develop the firmware in Segger Embedded Studio, SDK15.3.0.
On the pressure of a button on the sensor...
Mesh SDK:3.2.0
I want to send dimming level to server, and want return data of dimming level with mcu voltage.
When I receive server set callback, I tried: status publish...
I am developing a beacon-related project, my nrf51 device needs to play beacon. Beacon will determine the distance from NR51-> Smartphone. If distance = distance I give, I...
Hi all.
I am using a nrf52840 with mesh sdk 3.20 and sdk 15.30.
I am implementing RSSI tracking and require reference nodes to advertise once on each channel (37,38,39...
Hi guys,
I am using nordic semiconductor nrf52840 development board and segger. Is it possible to display the data of ultrasonic sensor on the nrf connect app by configuring...
Esteemed Colleagues,
We are using PCA10040 (1.2.4 2018.16) to develop a customized NFC Type 2 TAG. SDK 15.0.0 was used because we needed to work with hal_nfc_t2t.c instead...
Hi Team,
I am developing a low power application where we need to update Firmware frequently based on use cases.
I have successfully tested BLE secure DFU example and...
Hi,
We're trying to characterize the radio timings of the transmission of a Bluetooth Mesh packet from an originator in a Bluetooth Mesh network. Looking at the broadcast...
