Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Dear sir,
The current BGA ball size is 0.3mm. What is the recommended VIA hole size for the inner pads for routing the signals out from IC ? or How large of the via in...
Dear Company,
I would like to ask about start-up time of this product nFR24L01
Max 1.5ms start-up from power down mode
Max 130us start-up from standby-I mode
1...
Hi, everyone
how to increase the peripheral link count in multi role lesc example . even i have tried with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT by increasing the count, i am...
I have followed the dfu bootloader instructions for dfu secure ble example in both sdk 15.3 and 15.2 versions. I copied pca10056 folder to pca10059 and changed the board definitions...
Hi. I'm using nRF52832, SDK13.0.0.
I'm developing not only peripheral side but also central side.
I already made peripheral side referring to DFU example code.
But i...
I was trying to measure the current used by the nRF52840 on the DK. But it seems like i have messed up.
The debugger LED does not light up
The nRF52840 SOC seems to...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
