Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I got a nRF8001 Development Kit. On a peace op paper inside it says: "Follow the steps on My Page and add a product key. ...Download and read the user Guide"
I...
Hi,
I download the nRF9160 SDK month ago.
It can pass the SES build.
I saw there is new Simple MQTT example on github.
I download the new SDK from github today.
...
Hello,
I'm using a module with nrf52840 and I'm testing a vendor model implementation. The software interactive pyaci configure and send packet to device without problems...
Hi, I want to develop a software like nRF connect on windows PC for custom board test.
PC software will communicate with nrf52840 dongle via serial port,and nrf52840 dongle...
I want to include GetWifiAPs.c and GetWifiAPs.h files, which I developed by myself, in my project.
How do you include them?
I'm using SEGGER Embedded Studio.
I include...
Hi, I am working on a project in which the device (nrf52832) needs to be both central and peripheral and it can transmit/receive some commands through UART to set the advertisement...
Hi ,
We are using the BL652 module with your nRF52832 chipset in our important product.
In our product the wireless connection is fundamental and we would like to test...
Hi,
I am using nrf52832 to achieve system-off with low power consumption. Nrf52832 and a rf IC communicate via SPI.
I configured a pin as the wake pin.
nrf_gpio_cfg_sense_input...
Hi, I am trying to use github.com/.../nrf52-ble-image-transfer-demo with Ubuntu 16.04 Using - gcc-arm-none-eabi-6-2017-q2-update - nRF5 SDK version 15.0.0 (nRF5 SDK version...
I use SDK 15.3.0 with the example of USB_CDC. In the example, the virtual com port transmission works only when the terminal sends a DTR signal. I need the DTR notification...
Hi
I am trying to implement DFU to my project. I have done all the steps to generate packages, private and public keys etc. My program now starts at dfu and I can upload...
Hi,
setup: nrf52840 dk, no battery installed (power comes from USB connectors), switches are in default mode (SW9: VDD, SW6: default).
Flashed open_bootloader (dfu/open_bootloader...
Hello,
I'm using S112 V6.1.1 with the Nrf52810. I get a error using sd_ble_gap_adv_set_configure() after a connection. On BLE_GAP_EVT_DISCONNECTED i try to change the advertising...
