Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
Furhter to this post , I still getting unexplained behavior.
I use timeslot api to generate a burst of 10 hard-real time-pulses 29000us apart.
For the first 9 pulses...
I am using the nRF51422 device with the SDK 11. When building the ble_app_proximity using Keil uVision I am met with the following error: " Code size of this image exceeds...
I've downloaded both v15.2.0 and v15.3.0 documentation packages and the pages that reference svg images do not render in Chrome (for example ./nrf5/iot_intro.html). When I...
I am using the nRF52840 dongle to gather data via peripherals and send it via a serial port similarly as the cli example, for that I'm using the nrf_cli_fprintf() function...
Hi all.
I want develop device with nRF9160. goal - to get smallest size with chip antenna.
I not so good in RF design, so usually I using recommendation from datasheets...
Hello,
We have an nRF9160 DK and have successfully set-up the tools necessary to re-flash and write firmware for the DK using Zephyr and SEGGER Embedded Studio. We are planning...
Hi
I have tried to pull down the updates for the Zephyr project to for the mqtt_simple example. when I do a git checkout master and a git pull all goes fine. but when I...
Sir,
I have seen example pgm for communication between UART and BLE, and another pgm which communicates between 2 UARTs. But for my project I need 2 UARTs and the BLE together...
Hey,
previously working with BLE devices I had manage them reading/writing its characteristic. To control my new device I have to write the value into its handle ( i. e...
Hello Sir,
I have a PCA10090 (nRF9160) DevKit and it was working fine with Asset Tracker Example. Kit sent data to nRF Cloud last month. Today i have again verify the...
Hi, I developed a simple app that connects to a Bluetooth device, receives some data from that device and output it to the uart. As a receiver I have a custom board with a...
I have to develop a project for nRF51822 but I can't find tools that work. I tried SES and Eclipse and none can compile the examples of SDK12 (the last one that supports my...
Hello,
I've recently purchased the fanstel BT840F evaluation board which is based on the nRF52840. I understand that you cannot directly program the BT840F evaluation board...
Hi!
I just saw the MQTT example that has been merged in the master branch and tried to run it on my DK (NB-IoT). Without changing anything in the code or configuration the...
Following my last post a few days ago, I was finally able to communicate with a slave via the TWI interface, thank you very much for your help! This time, I have a problem...
