But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,I did different research on wheat and ant. And I have two questions:
Can the BLE and ANT protocols be used on the same S140 softdevice on an NRF52840 board? (At the same...
Hi Dears;
My name is Saif Muqdad, I'm an MS.c student, I'm asking if I could to get the Hardware details of NRF24 module, Hardware details like Power Amplifier class? RX...
Hello all,
I have a custom nrf51822 board with me and I am trying to flash it with ble_app_hrs example. I tried both sdk 11 and sdk 12.3 and used the softdevice s130 as...
I am transitioning a project from normal BLE to BLE mesh.
Flash space might be an issue.
Here is the flash layout I have so far. Purple is for nordic items and yellow...
I'm using SDK 15 on an nRF52840, compiling with Segger Embedded Studio.
I've created a project in SES using the project_template folder.
When I try to use both ESB and...
Hello,
I want to access the AIN input 6 ADC/LPCOMP input 6 to measure a current at two points with a defined time interval in between.
Since I am not familiar how to...
Hi,
I am trying to use UART in a blocking mode for nrf52840. I am able to transmit the bytes, but not receiving the bytes. While debugging, figured out that RXDRDY event...
Hi,
i have some issue regarding DFU-ing the bootloader.
Here is my command to generate zip file: nrfutil pkg generate --hw-version 52 --bootloader-version 1 --bootloader...
Dear Nordic Team:
I used nrf52832 as my BLE IC, and an IC of Novatek as my MCU. They are connected by uart. Now I need to merge ble_dfu and serial_dfu on the version of...
Errors while starting debugging session
I am getting error 65 'access violation' in Keil Uv5 and 4.
In IAR , I am getting 'User Error:Stack Pointer is setup into incorrect...
Hi,
I modiy the usbd_hid_generic example to tow endpoint by sdk15.0.When i use the USB testtool send some datas to usb deivce,the d atas cannot be read properly by NRF_USBD_EP_OK...
Hi, in our one project we are using nrf52832 radio to transmit the data packets. After transmitting the data packets, the nRF52832 chip need to disable the radio to minimize...
Using SDK 15.0.0, I have ported the peripheral/usbd example to custom hardware based on the nRF52840-QIAAC0.
In the nrf_drv_usbd_enable() function, execution hangs at
...
I'm communicating with a temperature sensor using I2C/TWI and I'm now trying to send that received data over BLE using the HTS service.
When I send a ble_hts_meas_t with...
