i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
I am using nRF mesh Android app version 1.0.3 and nRF mesh IOS app version 1.0.2
I have flashed the devices with light-switch example application under nRF5 SDK for...
Hi, I have pca10059 dongle. I soldered goldpins to swdio and swdclk lines to be able to flash it using external nrf dk. So I connected external jlink programmer and was able...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
Hi Nordic Support, community,
After I flashed, the connectivity hex, ble_connectivity_s140_usb_hci_pca10059.hex from the SDK v15 downloaded after executing the patch on...
development software, with versions (SDKs, IDEs, SoftDevices, ...):
Computer platform, with versions (Windows/Linux/OSX, ...) Windows 10 Pro x64
hardware revisions (chip...
Hi,
I am trying to make a weather station with nRF52 feather and BME280. Currently I am making a measurement program. The base code is Custom:Heart Rate Monitor Example...
Hi friends I use nrf51822 with sdk12.3 version and I want to use infrared receiver.
What method should I use to write the infrared receiver code?
Also, does nrf51 have...
Hi,
I'm able to send arbitrary information to the host using generic HID descriptor (uses vendor defined page). There is no driver issue. I'm also able to connect to the...
I am currently downloading softdevice (S140) on our custom board using P19 connector on nRF52840 DK. Our custom board also has nRF52840. It seems the dsoftdevice is downloaded...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
Whenever I deploy an example to the Fanstel BT840F with Segger ES, the S132 SoftDevice is always also deployed to it. I have attempted to change references to this in the...
Hi,
nrfx_uart.c has a bug where, once there is a RX error, the receiver gets stuck in a disabled state forever. This is because p_cb->rx_enabled is never set true, so the...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
