This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hey,
I was on one of the meetups when nrf52 was presented. You guys used a mbed shield for demos. Do you have code example and what pins you were using for connection?
I am working with the PCA10028 board, SDK 10.0.0, and s110 8.0.0. I have created a characteristic that is "coupled" to LED2. When a connected central writes a value to the...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hi, All!
I am using nRF51822QFAA with 16KB ram, and S130(sdk 11) for the dual bank bootloader, reference to the s130 releasenote, I config the ram memory start at 0x200013d0...
Hi,
I have tested several BLE examples in SDK12.30 and they would not compile, what's the problem?
for example here is the output of ble_app_uart example.
*** Using...
Hi,
Using this doc it says the SPI supports 16 bit frames. Is this true for the nrF51822 BLE Nano? I found that the mbed API does not support 16 bit frames doc . Can I...
Hello,
I tryed to find in Q&A something that can help me understand how it is possible to measure battery voltage with nRF52, but i am not sure i found the exact explanations...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
What hidden settings am I missing this time in the awful Segger studio ?
I get an error :
unknown type name class
When I compile with this new class called...
hello i am new to spi, i am doing project on 3 wire spi interface. I am using 3 wire interface as Sclk,ssn,MOSI pins only , I am not using MISO pin .I am tested spi example...
hello, I am working on nRF52 DK spi protocal.I am using AD9837 as slave.Here i am using 3 wire interfacing.I am connecting Sclk,ssn,MOSI pins olny & I am not connecting MISo...
what's the maximum data rate of nrf24l01+ (with ACK and without ACK) using 2 nrfs?
if i use 4 nrf24l01 two in tx side and two in rx side.what would be the maximum data...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
