Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
I have a custom board using the nRF51822 as a peripheral with the S110 SoftDevice. The centrals are mobile apps, both Android and iOS. The device spends a lot of time in a...
Hi
I'm trying to run uart example on nrf6310.
I followed following link.
devzone.nordicsemi.com/.../
and I defined ENABLE_LOOPBACK_TEST.
it was resulted in blinking...
I am using sd 7.0.0, I have a simple bootloader implementation that follows the bootloader sample code pretty closely. When I jump to my application from the bootloader and...
Is there anyway to get a light to blink using only the PCB antenna module?
Also, is there anyway to blink a light using only the Bluetooth Smart Beacon chip?
Hi,
I'm attempting to use 'S120/experimental/ble_app_multilink_central' running on a pca10001 to better understand the central / peripherial comm sequencing on the nrf51...
Is there documentation missing from the SDK 6.0 docs (and 5.2) ?
For instance:
https://devzone.nordicsemi.com/documentation/nrf51/6.0.0/s110/html/a00125.html
is blank...
Hi All,
I am new to BLE nRF 51822 development kit. It is mounted on nRF go Starter Kit. My question is how can I put a advertising 51822 chip to sleep? Also, when I turn...
Hi
In my custom project I'm using pins P0.14 as SCL and P0.15 as SDA .
I know the pins selection #define is in twi_master_config.h. But the question is whether I have...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
Right now I'm running without softdevice enabled. I'm trying to use RTC1 Timer for my own delay_ms() function...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am currently using s120 to create a central device to scan for my peripherals. In addition I am trying to parse the Advertising Report data and send it via UART.
p_ble_evt...
I have use PAC10000 and RF51822 EVB ,when i run sniffer.exe,and I found nrf51822 ble,[0],
select "w " and show " Starting Wireshark",but always show " Starting Wireshark...
Hi All,
I need the slave node(S110) send advertising continuously and monitored by master node, so I set the advertising parameters as:
adv_params.type = BLE_GAP_ADV_TYPE_ADV_NONCONN_IND;...
hi all,
I use the Nordic BTLE SoC(nRF51) for develop product and now i have some issue for the the btle compatibility with other vendor btle.
Whether i use the dongle...
I would like to send the application, soft device and bootloader firmware versions
by means of the device information service.
How do I read the soft device firmware version...
