i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
1. I have some puzzles,please give me some explanations,thank you!
In my design,I use some 51822 devices as tags which can communicate with the host.
The tags can send...
Hi, I want to know what's the differences between the NRF_CLOCK_LFCLKSRC_RC_250_PPM_xxMS_CALIBRATION and NRF_CLOCK_LFCLKSRC_XTAL_xx_PPM where xx means a decimal number.
when...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi,
I want the NRF51 to respond to a received packet from a particular device using register TIFS to control the interfame timing.
For TIFS to work I have to set the...
Dear Nordic,
is it possible to build a simple data bridge at speed of 115200 and up based on nRF51822 with CTS/RTS support and a fixed pin code for nRF51822 pairing?
I am working on a multi-node network application with multiple transmitters and receivers and I have a question about timing for chips like the nRF24L01+. I would like to...
Hi
In my case i have gpio interrupt for every 25ms. so i change button detection delay t0 10ms.
and i given timeout in all while loops of twi_hw_master.c.
but my...
Hi,
we have nrf51822 custom hardware.
we are flashing application through j-link.
but after every flashing , i need to do switch off and on the device.
then only...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
Hi,
I need to send more than 500 packets(each 20 bytes) to the master for every 1 minute, through the timeout handler. But i cannot able send all the packets, btle_connection_timeout...
Hi,
i have some trouble with the method __WFI ();
I have the following code:
while(device_status == false) // Gerät ist im Schlafmodus
{
checkPowerConnector ( );
__WFI...
1.Can we use the Timer0/Timer1/Timer2 for doing something?
2.What source of IC the SD have used?
3.What source of IC we can use for our application?
4.I used the compare...
