But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...
Using the Online Power Profiler for LTE we saw that nRF9160 would require 0.115 s to upload 4-kbit of data into the mobile network.
This is an U throughput of ~34-kbit/s...
Hi,
I want to make an I2C communication with an NRF5340 DK as Master and an NRF52840 as Slave, but all the example i found in I2C communication it use the slave adress...
Hi!
I’m developing an application using nRF SDK 2.9.0 with the Xiao BLE Sense . I created a new project based on Zephyr’s UART peripheral example.
The application runs...
Hi everyone,
I have found a Linux driver for the TLV320AIC320 external codec provided by TI:
TLV320AIC310X Driver: https://web.git.kernel.org/pub/scm/linux/kernel/git...