I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
How can I properly set up the SWD interface for printk on a custom PCB? I have to build my project example and see the message printed on the VS Code console. My custom hardware...
Using nrf5340 as both Central and Peripheral roles and I have implemented the Basic Audio Profile based on the nrf5340 audio example. I am using nRF Connect v2.6.1.
I...
I need a bluetooth module that is capable of simultaneously streaming audio two way, ie two channels stereo out and 1 channel mic in with low latency. A friend had recommended...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
Hi,
My custom board nRF52840 works as a Peripheral, which advertises itself for connection from a Central.
The project is built based on peripheral_hr sample project....
Dear:
I can upgrade applicaiton ONLY sucessfully through DFU.
but now, i want to upgrade applicaiton+softdeivce+bootloader to deployed devices. do you have such documets...
Hi,
What is the maximum PWM frequency one can achieve on the nrf52840 with 50% duty cycle? Sample .dts and c-code in NRF Connect SDK would be appreciated!
In practice...
HI.
we're developing an application where we need to use 2 UART ports: UART: 0, 2, 3.
Before we added MCU boot in our project everything worked well but after we integrated...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
I have a thingy91 device and want to implement the following requirements.
Expectation:
NRF9160 should remain in deep sleep mode and on the button click event do the...
I am developing firmware for a BLE peripheral using ncs v2.6.1.
In addition to using the libraries introduced in nRF Connect SDK Fundamentals and BLE Fundamentals on DevAcademy...
Hi,
I am considering to build a line of products using the nRF 5340 product and I am considering the options to perform FOTA.
So far the option I learned from the Intermediate...
