Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
hi,all
I'm using nRF52833, s140.. pca10100.
I want to read my pcb's touch gpio..
If I touch it, it falls down to low. ( I checked it with scope..)
When viewed through...
I'm testing USB audio demo. I changed bit resolution of APP_USBD_AUDIO_FORMAT_DESCRIPTOR 16 to 24 but the widows10's USB audio device is still 16 bit. how can i do that?
Hi!
I'm trying to pass the BLE data to the PC using nrf52840 DK.
To do so, I've started with the ble_app_uart example and it was able to build fundamental features–find...
Hello,
our application requires to emulate keyboard, e.g. to write strings like "hello world\n" as it might be typed by the keyboard. According to the recommendations...
Hey I am using nRF 52840 DK
I am reading temperature from Segger code and displaying it in the log
But I want to display that value in my android nRF Mesh Application...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
I created a 500ms timer to send mouse movement as follows.
m_mouse_movement_send(5,0);
When the device runs there, the device will restart. The error code is NRF_ERROR_FORBIDDEN...
Hi engineers,
I want to use the pin P1.09(NRF_GPIO_PIN_MAP(1, 9)) as GPIO, but when I initiate it, it seems fail.
I've looked through the relevant issues here, but got...
Hi,
I am currently trying to build a project using a nRD9160 with legacy code and am receiving this error when trying to load an existing project:
I understand...
I am not able to successfully use your nRF UART app to communicate with your nRF52840 DK. I get a warning when installing the app that it may be too old for my version of...
I'm still learning BLE development so I apologize if this is a basic question.
Here is a screenshot of a recent capture I did with the nRF52-DK. The bluetooth sniffer is...
Pardon my ignorance of the nuances of Security and Encryption but what I am observing is a bit perplexing.
Every time I run the nrfutil command to generate the bootloader...
Hello, I use sleep_mode_enter() to put the device into sleep mode, however, the RTT print a fatal error after sd_power_system_off(), I don't know whether the device is in...
I'm trying to open a nRF Connect SDK project in Segger Embedded Studio for ARM (Nordic Edition) V5.30a
When I try opening the project I get an error box with the following...
I want to add an OUT endpoint to the USBD example, but it is not successful. I cannot find the relevant tutorial. Below is my main.c, asking for help, thank you very much...
