Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
the pull-up resistance Rpu of GPIO pins as stated in Product Specification v3.1 in Table 62 is supposed to be 13 kOhm (typ). Since we measured a different value on pin...
I started development with the S132 (SDK 15.0.0) peripheral example "blinky". After some modification, it handles all necessary communication with my phone flawlessly. Now...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
Hi,
I have designed a customized for nrf52832 with a trace antenna. I haven't used any low pass filter and made the changes inside sdkconfig.h file to use RC and that board...
Hi,
I'm using nrf51822 module purchased from www.waveshare.com/core51822.htm . I'm running uart over ble application example. I commented uart_init() function in main(...
Hi,
I have the following setting. I have a dongle with with a nrf52 which sensd all data received from the NUS service to the host via a uart and a FTDI. The FTDI is capable...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hello,
I would like to disable and enable the nus_data_handler in my code to work with several interrupts, so I need to disable that handler and then reenable that again...
hi,
I am using nRF51-DK board as external programmer to program Minewtech Minibeacon having nRF51822 chipset (QFABC1, 128KB flash and 16KB RAM).
Tools:
SDK: nRF51_SDK_10...
Hello, Is it possible to use a RedBear V2 with the DAPlink as a Bluetooth dongle, apparently, the DAPlink can function as a USB-UART bridge. I'm new to SoC and am trying to...
Hi
I am trying to load my shiny new NRF52840 dongle with a simple blinky app using the nRF Connect (v2.4.0) but I get an error stating that the 'Region starting from 0x0...
Hi,
I follow exactly the same as "Interactive mesh provisioning and configuration" and stuck at "Adding a Light Switch client (optional)" part.
Everything looks fine,...
I am working on a J-link command line.
i just want to lock a device after a write a binary file into device.
In j-link there will be option for a unlock a device like...
Hello,
I'm developing a program using nrf52832 DK and SDK V15.
I want to activate the SPI transmission when NRF_RADIO->EVENTS_END occurs using the PPI. I follow the PPI...
