I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
In my application, I'm setting a message as manufacturer's data to be sent with the advertising message. To do that is simple, since I have a data type ble_advdata_t , and...
Hello guys, I was doing some testing with the QSPI component, and noticed exceptionally high current draws depending on whether the Peripheral was on, off, and if the Macronix...
I’m designing a board with nrf52840. For the RF layout part I’ve followed the reference design apart 3 pads near the pcb antenna.
The question is: How much is indicatively...
working environment:
SDK:12.3
WIN8.1
hardware:nrf51822_qfaa
nrfjprog:9.8.1
problem:
using nrfjprog to program application(s130 + bootloader + application),application...
Hi,guys
I got a problem. I tried to create a service to control led over BLE, when i finished, it can advertise, everything was ok. But when i tried to write 0x01 to control...
BT832 connect to a passiv MEATER temperature senor. How should I configure the Device with AT-commands. I use Docklight to send AT-Commands from my BT832.
Hi Team,
I want to connect the nRF52832 based custom board to AWS-IoT cloud.
The Simcom 2G module is interfaced with nRF52832 over UART.
Can someone guide me from where...
hello everybody,
In my application i want to check if a password is set, to enter bootloader, otherwise don't start the bootloader.
This should work without bonding. ...
Hi, I'm new in the use and development of chip.W here do i start to develop myself?
eg my first aim is to make bluetooth headset compatible with android. Can you help me...
Hi, I have been looking at the following document nRF9160_OPS_v0.7.1-1510217.pdf which I had downloaded from the Nordic website today. In particular the layout guidelines...
Hi,
I run the "ble_app_uart" from sample program and leave it as it is. The program ends in NRF_BREAKPOINT_COND with "Fatal error" after a while. It is displayed as a screen...
Hello
I am using the nRF52832 with SDK 14.2, JLinkRTT Client, and SEGGER IDE. The system simultaneously runs a soft DAC, IMU, digital potentiometer, and provides variable...
Hi all!
I want to use the BLE stack by Nordic. I figured out that S132 is the appropriate HEX image for nRF52832. I can burn the softdevice into flash with nrjftool.
An...
