Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi all. I try to configure QSPI example to work with w25q64fv flash. I connected all pins from flash to same pins on nRF as on PCA10056 DK board. After all i have "Data inconsistent...
Looking at the code in SDK 15.0.0 I think app timer library will be reinitialized. Is there a way by which I can check it the library is already initialized and initialize...
Just installed Mac v. 2.4.0 of nRF Connect, and the "Start Scan" button is disabled. Here's the log:
2018-07-05T13:43:15.834Z INFO Application data folder: /Users/rob/Library...
Hello,
I am developing on the nRF51 and soft device version 8.0.0.
I have created a new service that has a 128-bit UUID that is based on the base UUID: 00000000-0000...
Nrf51822
SDK : nrf51_12.2.0
soft device : s130
Example : ble_app_beacon
I’d tried single channel adverting with nrf51 beacon. And I referenced this way to disable...
We are using the nrf51822 chip, however after typing the command: nrfjprog --memrd 0x10001080 -f NRF51, the chip is no longer able to start.
We have tried resetting the...
Hi Everyone,
I have successfully configured RTOS and BLE alog with onboard LEDs blinking into an RTOS code.
Everyhting runs fine if i run only the 4 tasks of LED blinking...
Hello!
I need to send 20 x 20 bytes with the nRF8001 and would like to reduce the transmitting time as much as possible to set the MCU and nRF8001 in sleep mode as long...
Hi,
I am confused about the ROM layout, would you please correct me? Thanks.
Based on my understanding, for open bootloader scenario(like nrf52840 dongle), the bootloader...
I am using the nRF52832 with the S132 soft device. I am trying to send a large amount of data (~5 kB) from a phone to my BLE peripheral. I am wondering if the queued write...
I Have attached my project which is an SDK 15. project, starting with the simple twi sensor project and including some functions calls from gpio from SDK 14.0, porting gpio...
Hi,
The following is the guide under this ticket: devzone.nordicsemi.com/.../where-i-can-find-the-example-of-usbd-dfu-for-pc-side
Terje said "you can use nrfjprog with...
Hello everyone
The following warnings and errors occurred
Warning[Pe223]: function "sd_flash_write" declared implicitly D:\ZIP\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hi I am developing on Adafruit LE UART Friend ( https://www.adafruit.com/product/2479 ) platform. Compiler: GCC 7.2.1 IDE: NetBeans NRF SDK: 12.3, SoftDevice S130 Debugger...
Hi,
I am trying to interface ESP8266 WiFi Module: https://www.amazon.in/OLatus-ESP8266-Wireless-Transceiver-Raspberry/dp/B072BG8LW1/ref=sr_1_1_sspa?ie=UTF8&qid=1531738374&sr...
