Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
I am trying to free up some RAM on my nRF because I am getting Fatal error 0x4, NRF_ERROR_NO_MEM when I try to increase the size of a 2D array.
I do not understand how to...
Hi there,
I am considering the NRF52840 to build our new platform but I am struggling to find information about how the device Firmware is programmed.
Apart from SWD...
Hi,
I'm using sdk 15.2, with soft device s140 on nrf52840 dongle in peripheral mode. I'm using modiffied ble_app_proximity example. What I wan't to achieve is to set advertising...
I want SoftDevice of Bluetooth 4.2 for nrf52832.
I found softdevice.
15.2.0 nRF5 SDK
15.1.0 nRF5 SDK
15.0.0 nRF5 SDK
14.2.0 nRF5 SDK
etc
Which is Bluetooth 4...
i have one huge process one get positon sensor using i2c bus and another get led color also using i2c bus.
when color function is added in the process,positon sensor data...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
Hi,
I found this example here for nrf51.
github.com/.../nrf51-ble-gzll-device-uart
And this is more or less what I would need for my application.
Is there a way that...
Hi All,
Scanning with a nRF52840 Dongle, Is there a way to know if one of the scanned devices is using Coded PHY modulation to advertise? And if the answer is negative,...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARM Cortex -M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
Hi,
I am using "ble_app_uart" code and added battery service to it as custom changes.
I want to update battery level at every 3 seconds.
Code is working fine and starts...
Hi - In the examples provided, a peripheral will go to power off after completing its transactions.This means the the application does not have to "clean up" afterwards. ...
