Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I downloaded the application using nRF5_SDK_12.3.0_d7731ad \ examples \ dfu \ bootloader_secure...
Hi, the peripheral/spi example calls for nrf_drv_spi.h, which is located in the legacy directory in SDK 15. I found this post in the devzone:
[quote userid="2116" url="...
We're trying to implement OOB pairing where the 128-bit value is received externally (not NFC). All examples I could find are NFC related and seem to require the external...
Hi, everyone. We are developing BLE project on the chip nrf52832 with SDK 15.0.0 software. In this project we are using ppi feature. During the work the program must enable...
I am trying add the fatfs example in my custom solution and I have the follow error after add the paths and files.
nrf_log_frontend.c:92:35: error: unknown type name 'nrf_log_module_dynamic_data_t...
Hi,
I am working for Adafruit on the bootloader for the upcoming feather nRF52840. Currently testing using the nrf52840DK pc10056. Everything is OK with S140 6.0.0 . Today...
I need to implement a 4kHz signal to drive a buzzer on a custom board of nRF51822 with external 16MHz and 32kHz crystal.
I am using Timer1+PPI+GPIOTE to generate this 4kHz...
I'm currently using:
- Board: NRF52840
- SDK for Mesh 2.1.1
- SDK for Thread and Zigbee v1.0.0
My problem is that I want to merge and run both Bluetooth Low Energy...
Hi, I am using nRF SDK 12.0.0_12f24da, with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c
Initially I was working on integrating...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project:C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\ uart \pca10056\blank\ses ...
Hi all, I'm using nrf52832 with SDK15 in my project. For debugging purposes I need both CLI and LOG modules enabled with RTT as a transport. I followed this manual to setup...
How can I disable NRFX_LOG_INFO calls in the PPI driver? I've set NRFX_PPI_CONFIG_LOG_ENABLED 0 and even NRFX_PPI_CONFIG_LOG_LEVEL 0 but that doesn't stop messages like the...
Hi,
This is Srivisakh. I am using a custom made board integrated with nrf52832 board in which UART is configured. I am using Segger IDE for code development and building...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
