Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
hello there,
i am using nrf51422 but dont know how to write a program for uart. i want to send AT commands to Quectel M95 using uart .
good help appriciated!!
cheers...
Hi. I'm using nRF51822.
My solution needs power on and off continuously.
I think that is not so good at chip.
Do you have any data for how many times it can bear for PWR...
Hi, I'm using nrf52810.
Size of flash memory of nrf52810 is 192kb according to the datasheet.
But size of hex of S112, nrf52810 softdevice, is 281kb.
Why size of S112...
Thanks for reading my question.
I use SDK14 , PCA10040, S132 and modified a little bit of uarte driver, but that should not affect what I said below.
I set the DMA buffer...
I read about Segger studio (on their website) that it reduces the code size. I try to check it out
Here's my opposite result
I've compiled the same app (e.g uart_example...
Hi all , when I run and debug my code , I frequently encounter error :
I think it's related RAM configuration on KeilC .
Please show me what is error ? And how to solve...
Hi there,
So I'm going through that complicated step of setting up the IDE for the first time to get started programming and I'm having issues doing it with the SES and...
hi everyone ,I want to ask you a question, I use the SDK12.3, when the device from the application transformation to the bootloader, when DFU is failed, why the deice is stays...
I am using nRF51822 (PTR5518A) with SDK v12 and s130 softdevice. To dump the code I am using nRF52 DK segger (PCA10036). With that I am able to dump the code but there is...
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
