Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hello.
I have downloaded and installed Nordic STK and nfrfprogtools.
Now i am trying to through devzone.nordicsemi.com/.../ tutorial.
I successfully loaded s130 softdevice...
Hi,
Is there any method that I can use to get the LE Packet or the Baseband packet ( With Access Address) passed onto the application? (Using S110 or S130)
Thanks
I started by compiling BLT uart app successfully on MDK5 but found out that it is giving errors on the startup files in the Device Pack.
I tried to refresh and update Device...
Hello Everyone,
I am trying to measure the (3v)battery voltage by having proximity example as reference but intially it is showing 100percent later it is going to 13(percent...
Hi,
SDK: v11.0.0.2-alpha
DK: PCA10040 (NRF52)
I am trying to build a peripheral application that communicates with an external device via UART (h/w flow disabled)....
Hello!
I have PCA10006 with revision QFAA nRF51422
I am testing the buck converter's ability to make the system consume less power when transmitting.
Example is ant...
hello there! i am working on project in which my one nordic BLE(A) want to send command to second nordic BLE(C) which is not in my range. now there is third nordic BLE(B)...
Hello Guys,
I would like to know, can i use NRF52 Preview DK on Board Segger Section as standalone Segger JLink Programmer for NRF51?
So, is there any way to dis connect...
Hi, I read about concurent operation of the Softdevice and other proprietary stacks like esb or gazelle using timeslot api. Is it possible to run two ble stacks in this way...
Hi Guys,
I would like to develope a HID device on nRF52832 chip. I'm woring with nRF52 Development Kit (PCA10040, v0.9.0).
I've tried to flash the board with both hid...
I'm getting the NRF_ERROR_NO_MEM when I try to put my ADC interrupt routine into the scheduler. The code runs without error if I run from the ADC interrupt handler directly...
Hello ,
I am testing the DFU support and usage for the next phase of my project. I am using S110 softdevice 8.0 and SDK 9.0 and evaluation kit nRF51822QFAAG0.
I followed...
hello, I have some quesetion about the nrf51822's carrier detect. I want to use " CSMA" to avoid
Communication collision, the datasheet has no detailed infomation about...
when I call pstorage_store so store a block of data, sometimes I call just after pstorage_store : the following code
do {
pstorage_access_status_get(&count);
} while...
In this post , I can register a new case with some required parameters to have the current estimation, but I don' t know how to obtain some of them.
I'm using nRF51422...
