We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi all,
I have been stuck trying to debug the example project for a couple of days now and could not find the answer through searching. Here are my problems.
Background...
Hi All
I have a bunch of nrf51x22 (4,8) and I'd like them to read their own firmware data and send this to others that are in DFU mode using the over the air (OTA) method...
Dear Nordic Developer Zone,
I'm using nrf51822 EK testing the GPIO sense function. The code I'm using is based on what a nordic employee has posted elsewhere in this dev...
hello,
i was trying to compile the softdevice s130 example code given with softdevice download from nordic.
I am using the ARM-MDK lite 4.74 version. It is showing error...
My design goal is to conserve as much battery power as possible on a device that typically gathers data 30 to 40 minutes per day. To that end, our thought was to make the...
hi~
6.2.1
Updated Setup_JLinkARM_V490e to Setup_JLink_V492
Updated nrfjprog to version 5.2.0 (see own release notes for changes)
where is release note ??
i can...
Dear all:
I want to constantly transmit messages from a nRF51422 to an other nRF51422 with specific ID by ANT protocol. Then, I want to receive the messages from one to...
Hi,
I want to build a Tx that can reconfigure a channel(like change the device's number) after finding out a long time failed to send message.I use the way below:
sd_ant_channel_close...
hiii...
i hv made a custom profile with concurrent broadcast feature tested in master control panel and some other phone app... working properly.. but wen i tried in iphone...
Hi,
I try to open ANT+ channel and make sure the status is searching or tracking,
but if I use pstorage to update flash in the same time,
It will response timeout...
We are developing a keyboard for smart phone or plant and what to make different surpport for different device.
So can I make difference from ios device and Android device...
Please indicate me if there is a data port on nRF8002 after you burn out OTP, Can I use this I'c for data transmission. Please indicate communication port for this chip. Also...
Hi,
I'm testing ble_app_proximity example (...\Nordic\nrf51822\Board\nrf6310\s110\ble_app_proximity). I'm using Master Control Panel Android app version 2.0.3 and Nexus...
I'm using S110.
I have a characteristic that is writable from phone client. However, the characteristic has lower and upper limits (an acceptable range) for the application...
Hi experts,
I'm trying to bond device between my android phone and the Nordidc51822(S110 v7.0). but I found that it's very difficult to achieve this function. Is there...
