Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I have the nRF51822 Evaluation kit and put the Heart Rate Demo on the PCA10001 (V2.1.0). When I press Button 0 it doesn't advertise. I have the module (PCA10000) scanning...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I copy static void radio_disable(void) and void radio_tx_carrier(uint8_t txpower, uint8_t mode, uint8_t channel) into my project.
I call radio_tx_carrier(RADIO_TXPOWER_TXPOWER_0dBm...
Hi all,
I have a spurious crash in the softdevice I guess.
It occurs sometimes when the master (an HTC-M8 android phone)
rapidly submits characteristic changes
(acknowledgement...
SDK: V6.0
HW: PCA10001
APP: s110/ble_app_hrs
Question:
If use "twi_master_init()" with "twi_hw_master.c", the current consumption is added 1m
A. But if use with "twi_sw_master...
Hi I am completely new to ARM development world. I have been developing for years for PC.
Now I am working on a Project where we have decided to evaluate nRF51822 chip...
I would like to know if it is possible to use the internal RC oscillator without calibrating every 4s with the softdevice disable. I just want to read a sensor every 2s and...
I'm interested in using BT LE to collect data from a number of serial based devices -- a point-to-multipoint configuration. I'm familiar with the UART examples and have seen...
Hi,
i am searching for infos about my concrete BLE-Sig certification situation but i cannot see the forest because of all the trees :o)
i am currently developing a BLE...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
