Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
nRF51822 DK. Keil can download program. But in my pragram, when receive a UART command to erase
FLASH page 248, use ble_flash.c
static void flash_page_erase(uint32_t ...
Hello,
i try to get HRM example to work with eclipse. I can compile the project with GCC in eclipse and flash it to the PCA10001 eval board. I can find the HRM with the...
Does anyone have additional information on the relationship between SAMPLEPER and REPORTPER in the nRF QDEC?
I understand that the SAMPLEPER sets the base sample period...
Dear all :
I was recently reading ble_app_hrs example code , the PC1001 Board dowloaded this code can connect with other devices and they can send data from PC1001 to other...
Hi,
is it possible to handle a 2 second button press and wake up the device with the app button modul?
Or should i handle the button without the app button modul to wake...
Hi,
Last time I met "nRF51822 DK Setup Wizard ended prematurely". The problem was solved by installing .NET framework 3.5 on my PC. Now the same problem is come up "nRFgo...
Now i know the Cortex M0 does not have a floating point unit. Does this mean that we cannot do floating point calculations in our application? or is there a library that will...
Development environment : keil mdk 4.7, nRF51822, SoftDevice 6.0-alpha, nRF51 SDK 4.3
Hello
I develop the application with RF and BLE by receiving UART msg. So, my program...
Section 8.1.2 of the nRF51822 Product Specification states that the "Standby current for 16 MHz crystal oscillator" is 35 uA. The footnote says that the current is drawn ...
Hi,
I met this prompt(see attachements) when I install nRF51 SDK. Who can tell me what's mistake it likes? I have installed microsoft .NET framework 3.5 before in my winXP...
Hi,
i programmed the softdevice with nrfgoStudio but i get an error and i can't load the softdevice on the chip again.
The Error means that the cpu is not halted and that...
Hi guys,
I hope you can answer my question:
I made myself a custom pcb for testing purpose. I can program the nRF51822 just fine. Thats the actual state right now.
...
I have a nRF51822 dev kit, and my dongle is running the master emulator firmware, and master control panel is running on my computer, the dongle is connected and started discovery...
