I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I'm using nRF Studio Visual Studio Code. (SDK and Toolchain v.2.7.0) with the nRF7002 Development Kit. The Blinky example have worked fine and also the other things as shown...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
I need to install the Direct Test Mode App to validate the direct test mode running on a custom board. On the version 5.1.0 of nRF Connect for Desktop all app installations...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
I am trying to use my nRF52840 as a sniffer and am attempting to follow the directions at:
Programming the nRF Sniffer firmware (nordicsemi.com)
Note that I have downloaded...
Hi,
I want to use a LNA for make our sensitivity better, Then i should to put a RF switch and have a control in sending and receiving, because when the device is in receiving...
I am developing a USB dongle (nRF52833) for computers and a controller (nRF52833). As a basic configuration, multiple controllers need to be connected to one dongle. Multiple...
Hi,
We have a custom board (powered by nRF52840 with Softdevice and nRF5 SDK 16) that has an external ADC module to sample 30 kHz ADC continuously for 1-2 seconds. What...
I encountered the problem trying a Matter OTA-update and and asking myself why the bootloader wouldn't apply the image:
I am using the partition manager and defining the...
After flashing the nRF Sniffer for Bluetooth on nRF52840 dongle, I want to flash it back with the programmer to use it in the nRF Connect App but it wont go in boot mode....
Hi. I did some testing with two nrf5340DK boards to check the accuracy of distance measurement with Nordic's nrf_dm app. Even in non-high precision mode the reading with ifft...
Hi.
Our company has a couple of different custom designed boards using the nRF52840 and powered by a battery. OpenThread is used for networking, and the devices are configured...
Hello, I got a custom board based on nRF52840. It uses extended BLE advertising to deliver a sensor data to the central hub with a frequency of 10 Hz. I've set the interval_max...
I have a question regarding DTM using nRF Connect for Desktop. It is my understanding that the signal generated does not have a BLE packet structure but it is a continuous...
