Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hi i want to make a low power delay ms (blocking) function for nrf52805 without softdevice and without NRFx, just writing to the registers.
The RTC1 events_tick never...
What is the recommended way to do DFU over Mesh in Zephyr? I saw DFU documentation in nRF5 SDK for Mesh v5.0.0 but not sure how this relates to Zephyr
Can you point me to...
Dear Sirs.
I bought thing91 and nrf9160.
I have connected the thingy 91 with nrf9160dk with prog/debug cable but I dont able to debug the application on the thingy91....
Hi,
I have this development board https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK . I would like to use development board as nb-IOT modem and other MCU...
I am just getting started with the Nrf52840 dongle and trying to flash a few examples from the SDK. I was able to flash the "blinky" example just fine using the programmer...
Hi,
I have been trying to interface GSM modem with nRF52840 using LPUART (nRF Connect SDK). I have used below pins for connections:
nRF52840 - GSM
P0.21 (TX) - RX
...
Hello,
Now I am developing firmware for nRF5284 DK, and the one of the requirement is the voltage keep in 2.1V.
Is there any possible I can modify the voltage to 2...
Hi guys,
I'm thinking of implementing consumption optimization on a system that runs on nrf52832 with S132 SDK 16.
The idea is to call nrf_pwr_mgmt_run() to put our...
Good afternoon,
I am working with the NRF9160-SICA-B1A-R module on a custom board.
Checking the functionalities with a software developed on a Thingy:91, I get the following...
Hi, I have recently upgraded to a new system with windows 11. I have been working with NCS v1.8.0 on last system and installed the same in new system. all the necessary installations...
I have downloaded the WS2812 driver example and have successfully been using the nRF52832 DK to control these lights with SPI. I am ready to start developing on a custom board...
This was driving me crazy. nRF Terminal extension in VS Code just silently fails. I was able to use the JLink Viewer app so I knew RTT was working correctly.
I then looked...
Hi, I am using nrf52840 to senda imu data over bluetooth to computer. For the transmitter i am using NINAB306 with integrated PCB antenna as a central i use nrf52 dongle....
Hi,
while switching to the nRF Connect SDK, I cannot program anymore my ANNA B112 (which is a nRF52832) using my nRF52840-DK as a programmer.
The following are working...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
