I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
Hi, does Nordic provide the "works with all hubs" Zigbee cluster?
I see this blogpost mentioning " Watch out for more information on future Zigbee 3.1 SDK All Hubs support...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Board: nRF52840
Hi, I'm a newbie in zigbee stack. I have been get started with the door lock example.
I want to make custom...
Just wanted to share how to interface a thermistor (103) with Nrf52840 and get the values over a BLE android app (Nordic toolbox). refer here,
github.com/.../Thermistor...
Just wanted to share the project for interfacing IR distance sensor with Nrf52840 and get the values over BLE app (Nordic toolbox)
github.com/.../distance-sensor-with-N...
