Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
Are there any nRF51 demo firmware implementing paring function that the central and peripheral devices will connect automatically without user interaction when they come ...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
I have purchased a red bear lab ble nano board with nrf51822 and a PICTAIL board with microchip RN4020 chip. i have set Tx power 4 for both boards. The rssi value shown in...
This may just be a preference or architecturing question but I thought I'd ask in case there was anything I'm not thinking of, or benefit of one or the other.
I have 2...
Hello,i am find an interesting phenomenon recently.I have a Nordic 5182 device(role as peripheral) and bonded to an iOS device(role as master),when i put the iOS device near...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am working with nrf51822 MC. In my Transmitter code, i am using in low power mode. I was enabled the low power in my code (__WFE(), __SEV(), __WFE()). I measuring...
Hello, I need HID device with NRF51 Dongle.
when NRF51 Dongle insert PC, PC will check it as HID device.
So, could anybody can share suggestion how to add HID on NRF51 Dongle...
