I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
Hi
I have a serious problem with stability in "UART" communication over BLE.
I use the command:
err_code = ble_nus_send_string(&m_nus, &bleBuffer, 20);
where I send 20...
I have the following:
Dev board PCA10040
SDK nRF52_SDK_0.9.2_dbc28c9
Mac OSx
I was able to compile the blinky example and have the .hex in the _build folder...
I have several services on a nRF51 peripheral, and would like to have different initialization based on which service is being connected to. The related code is below:
...
Hello,
We have this board ( www.nordicsemi.com/.../nRF51822-mKIT) and would like to use P0.26 and P0.27 as GPIO (or RX/TX for serial). I've cut both solderbridges (SB2...
Hello,
I am having a lot of trouble with connection timeouts. With my current settings (10ms connection Interval and 6 seconds connection supervision timeout) I would not...
Hi,
With the latest nRF Master Control Panel App it's possible to simultaneously scan + advertise on some devices.
I thought this mode is only supported by devices with...
Hello,
am I right in assuming the following?
BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN is only returned when a Central is establishing a connection...
Hi, I use Gzll protocol to realize 2.4G frequency hopping communication， Two Device send data to One Host on Pipe1 and Pipe2.
1 Two Devices occur "loss power" many times...
Hi,
I'm working on custom PCB and I have small issue.
After making PCB I was trying to connect, but no luck - "(unable to connect to the target)"
Maybe there is something...
