In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hi
I'm developing nRF52832.
I have a question about SPI communication.(\nRF5_SDK_17.0.0\examples\peripheral\spi I don't understand, so I ask questions.)
I want to read...
We plan to use nRF52840 in our new project. But the application is likely to be larger than 500 Kbytes
So we are going to use the only one Bank flash for DFU as in following...
We are thinking of making changes to the QIAA aQFN73 circuit configuration from 5 to 4 and use the REG0 DC/DC. VDDH will be connected to a single-cell Li-Ion battery (3~4...
hi, i am working with nrf52840 and need a stand alone qspi peripheral in the project. what is the straight forward way to get qspi into the code up and running without involving...
Håkon Alseth was helping me with this: https://devzone.nordicsemi.com/f/nordic-q-a/83126/hard-fault-using-twi_scanner-example I accidentally clicked "verify answer" when trying...
Hi,
I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832...
Hello,
I am using nrf52840, SDK 17.0.2, softdevice s140 and also implemented OTA DFU in my application.
I want to save some data lets say admin code in flash. Once I burn...
Hello,
I'm having difficulty getting the GPIO set up in a way that behaves predictably on the nRF9160 DK. As far as I understand it, the nRF52840 is what controls the GPIO...
Hi All! My question is that while using coded PHY is it possible to enable the ACK? In case no ACK receives then retransmission of the same packet to the receiver. Thanks...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
Hi,
I see that in the latest SDK 17.1.0 there seems to be no example for regular UART but only for LPUART.
That made me wonder if there is any advantage in any scenario...
I have an external flash
S25FL132K
I am able to read , write and erase the flash with nrfx_qspi_cinstr_xfer function for 9 bytes. But I want to write more than 9 bytes...
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
