But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello all,
I've been modifying the thingy:52 mesh demo ( https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo) to support more sensors but I've noticed a severe...
The NRF52810, gives the 0dBm out, with 4.6mA peak current 。
When we using, we plan 20Kpcs for mass product, the current is more 4.6mA， it is 7.4mA 。
we use the 2MBPS air...
I would like to have multiple threads simultaneously accessing the modem via the AT commands over the AF_LTE socket. Thread1 does the normal AT+CFUN=1 and other active commands...
running DFU example from <SDK 15.3>\examples\dfu\secure_dfu_test_images\ble\nrf52840 , and attempting a DFU update of:
sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi everyone.
I have a problem with processing with recived UART data. I'm using software UART from example > peripheral > uart.
I use nRF to comunicate with GSM module...
Hello,
how can I store CCCD values in flash?
I read that the peer manager handles it ,but when i reset my device and load all bonded peer data, the CCCDs are not set....
Hello everyone,
i'm trying to hook up an external i2C sensor to P5 connector (TWI_SCL_EXT, TWI_SDA_EXT) and created a device driver template ( from drv_gas_sensor.c example...
What is the max amount of data that can be saved in records in fds?
When we do a dfu, is the data conserved or not?
How to vary the size of the records if possible?
...
Hi all,
Recently, I have concentrated on a mesh project using nrf52840 board programmed sdk_mesh_v_3.1.0. There is a situation that the board needs to send two different...
We have a project to explain the company Shenzhen Zhouhai Technology Co. to invite them as our partner because we see the smart bracelet CK series would be a good option for...
Hello,
We're using the UDP/IP/6LoWPAN layers as provided by the nRF5 SDK 15.0.0.0.
After experiencing sporadic issues in communication we have a question regarding the...
Hi,
I am using BLE_Blinky_Peripheral example from SDK 15.3.0 with s112 softdevice. I want to use basic softdevice APIs instead of nrf_sdh libraries for enabling BLE stack...
I am a beginner trying to get a device to operate optimally under a battery. Where can I find a starter code template that would shutdown/disable everything, putting the device...
