Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi all,
I have a trouble. I use 2 Dev Kit NRF52832. Flash light switch server proxy and light switch client proxy. Issue is when I erase and flash the first time, Client...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
I'm fairly new to working this close to hardware and am playing around with a few things. I'm trying to bit bang i2c over a couple of gpio lines and everything seems to be...
1.Does nRF52840 and nRF9160 have conformal shielding in manufacture procedure？
2.Do i need reserve shield cover for these two module when I develop product？
Hello,
I'm having trouble adapting my code which works for reading the MAX30100 sensor using TWI input with the NRF51 DK kit.
I would like to adapt this code to be used...
Hello, I am at a loss because this question has come up several times in your forums and the solution is not working for me. Every time I run my program I am receiving a NRF_ERROR_NO_MEM...
I have a nrf9160dk and I setup the whole tool chain by following the Getting Started Assistant. I can't figure out how to connect to the board. Probably just a simple switch...
We are in the final stages of product development and are planning to enter the first batch of production by the end of January. We have a custom board tested, software written...
Installed nRF5_SDK_15.2.0_9412b96 to use with the nRF528240 DK. The SPI example suggests using a makefile. My computer does not have "make", nor gcc. Did I need to install...
Hi all,
I would like to know if there is a way to use the NRF52180 as a central scanning device. I searched for central examples in sdk 14.x.x and 15.x.x but they have central...
HI,
I am using sdk 12.2.2 and nrf52. I have write characteristics in my beacon but I can only send 20 bytes in one write cycle. How can I send more than 20 bytes?
