I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
i have been trying this, putting the code from SDK14.2/example /periphelas/uart, but i had problems with the file links. So can someone helpme to impleent that or did someone...
Hej Nordicsemi,
We're developing a new product based on Bluetooth LE. And we would like to know if thousands of BLE devices can coexist in the same area. Preferable all...
No matter what sleep mode I put my nRF51822 in (system on, idle, system-off), it seems that the base current is above 1 mA. Is this how it's supposed to be?
I am using nRF 51422 SDK and SoftDevice v1.0.
I succeed in building and loading blinky example from SDK v12.1.
And I succeed in building and loading ble_app_beacon example...
With this Main.c, I'm only seeing the 1st 4 bytes of the device name in the NRF Connect app.
Note the use of:
init.advdata.name_type = BLE_ADVDATA_FULL_NAME;
Am I using...
Hello everyone, I added NUS library and I change the sdk_config.h file according to ble_app_uart example. When I built my project, I do not get any errors. But the device...
Hi support team,
In order to make the application hex valid after programming in a bootloader enabled project, we can use bootloader-settings.
As for secure DFU, it...
We are upgrading some products to SDK 14.2 and creating some new ones.
We need to start production programming of boards. I can't find the information on how to do this...
What is the maximum and minimum frequency of the PWM signal/square wave that can be measured on the NRF 52DK board I'm using NRF 52832.
Also, what is the max and min "pulse...
Hello,
I have found similar questions on transmitting multiple bytes over SPI, but I am still not sure how to do it. I want to communicate with a driver which needs to be...
Hi,
I found the 'Solar Sensor Beacon' example from
https://github.com/NordicPlayground/solar_sensor_beacon .
There, I found that no softdevice initialisation (nrf_sdh_ble_enable...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...