Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hello everyone,
we have an in-house HW with the nPM1300. Both load switches are configured as LDOs as described in datasheet chapter 9.3 configuration 1.
LDO1 is used...
Hi,
I have successfully implement the BLE video transfer using nrf70-wifi-ble-image-transfer-demo .
I can receive the image using the Android-Image-Transfer-Demo application...
I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello,
I'm using the SLM application with an NRF9160. I'm sending AT commands for MQTT publish. After ~10hours the device reboots.
The setup AT commands from powerup...
Zephyr Version 3.7.99, Zeyphr SDK v0.17.0
Thread Version v1.4
Matter SDK Version 1.4
After the switch from Matter SDK version 1.3 to 1.4, the NVS module under Zephyr...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi,
I need to use two or more different event lengths for different modes. The event length should be set based on the mode before establishing a connection. I found that...
I would like to know how to add an eSIM profile to an eSIM chip using the nRF9151 modem. Is there any platform or support that enables an infrastructure for this? What should...
Title: Issue with I2C (TWI) Communication on nRF52840 (SDK 16, Segger 8.2a)
Description:
I am working with the nRF52840 using nRF SDK 16 in Segger Embedded Studio 8...
Hi
is there an example for this: sending data over ISM band 2.4 gHz without BLE on a NRF52840 or similar?
I need to transmit 2 bytes board to board with jitter and delay...
Hello, I want to write an applicatin that gets at_coammnds from the terminal via uart, sends the command to the modem and then sends the respond back via uart. I have two...
Please provide an example of using app_sched_event_put() to pass a string.
This is what I have at present:
The handler appears to get the first 4 characters OK (perhaps...
Hello,
We have a sensor with 2 ADCs inputs meauring identical LMT70s on the board. With one of our older firmwares we get the accurate valudes of 22deg or so on both channels...
