Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
Hi,
I was using the nrfx_saadc_buffer_convert to make everytime a single sample.
Now I did find out there is also nrfx_saadc_sample_convert. How do I initialize this...
I've been trying to debug a recurring hard fault around nrf_log_frontend_dequeue. This occurs sporadically (between 10-60min) into testing my firmware. When the fault occurs...
Hi all,
normally our system runs in low power mode. When triggering the SAADC the first samples (using oneshot mode) will be off (slightly too low).
I can work around...
Hi,
I need to create run time count that increases every 0.065536sec.
I found a way doing so by using HFCLK without any interrupts.
My questions are:
1) Are there...
Hi, I am working on the nrf52840 dongle using the softdevice.
I would like to know whether it is possible to add OTA DFU capability to the default open bootloader that allows...
Im quite new to development with the DK so bare with me.
Currently I am able to read digital values (0 and 1) from the potentiometer using pin P0.03.
I am using the function...
I had toolchain manager 0.10.3 and a project using NCS 1.91. Unfortenuately I have updated the Toolchain manager to 1.0.0 and now my project does no longer show up and the...
I have a NRF52840 based custom device that I can program just fine with a NRF52840-DK.
However, when I try to use a NRF52833-DK I can erase and flash the softdevice just...
Hi,
I work with nRF52840 DKs and I am working for indoor positioning system based on RSSI signal strength. I want the RSSI signal strength to be sensed and transmitted to...
Hi Devzone team,
My customer wants to design the LTE-M antenna for their tracker project in US market, do we have any antenna reference or design guideline? I see we have...
Hi,
I am looking for a BLE module that I can program to send a Thyrmistor signal 250 meters or more. The BLE module has to be small and able to collect A/D Convertor and...
Hi ,
I am trying to get GNSS on thingy 91 to work. It seems like I have the same issue as this thread:
I cannot get a fix. Currently, I am using the 1.3.2 firmware ( the...
Hello, I am developing a product using nRF52840. I use the DK board to debug and download.
However, I would like to implement a firmware update function using USB on my...
Dear,
we have a problem at the startup for our nRF52833-DK board powered with coin cell battery. nRf52833-DK doesn't start up with coin cell battery when running ble_app_uart...
Hi,
I'm trying to do a 2 channels adc reading to read a value of a potentiometer and a value of a battery level. When I try to make it, I saw that sometimes, the value of...
