Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I am using Seeger for flashing Code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”.
In “ble_app_blinky”, as part of wait_for_flash_ready...
Hi,
How can I port the code written for nRF51 to nRF52>
Do have nRF52 FW backward compatibility.
And can i use same base code for both chips?
Is there any link/documentation...
Hi, I am testing NB-IoT on the nrf9160 and it appears the DNS is failing.
I have two networks here and with an NB-IoT modem from a different manufacturer the DNS is resolved...
Dear NRF gurus,
We are trying to implement a BLE node to bridge BLE 5 and BLE 4 - to leverage the long range of BLE 5 in the meanwhile working with the large amount of existing...
hello everyone, i am looking for the maximum allowed deviation of the uart. The nRF52832 is clocked with 32 Mhz and has a baud rate of 19200. What is the maximum deviation...
Hi
I am working on BLE Eddystone example program in nRF52832 using SDK 15.3.0.
can i change the password entered in the nrf Beacon for Eddystone app into ascii value.
hi ...
i want to connect multiple peripheral to one central , want to share the data. so i have merged the multi link central with central uart . while i am compiling i...
hi,
i am trying to integrate nRF SDK 15.3's ble_app_buttonless_dfu service in ble_app_blinky example,
after adding all source files and and preprocessor definitions while...
Hi,
we are using a custom nRF52840 board with SDK 15.0 and softdevice S140 6.0.0. Flashing the application including DFU and softdevice using SES produces the following...
I have a strange problem running the CLI example in the DK on the Nordic dev board with SES: It works fine with build/run, but when trying to debug it pops up a message that...
I am using the nRF52832 in several projects for several different clients. I have created a "project" under Visual Studio using VisualGDB for each one, using the automated...
Hi,
I would like to know how to raplace a MPU-9250 chip with ICM-20948 in a Thingy:52 circuit.
Let me first state that my electronics engineering knowledge is at hobby...
So I've had a LOT of problems getting power management to work with UARTE on the 52840. We're using both UART_0 and UART_1 and have finally gotten UART_0 to work as it should...
When attempting a DFU update (containing APP + SD + BL) with the android version of nRF Connect, it appears that connect will update the device's application even when bootloader...
Is it possible to pass a memory location to PWM (preferably via DMA) via PPI. This is a sound project and my intent is to update two 8 bit PWM outputs at 44.1kHz. I typically...
