Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hi, all,
I am new to nRF Connect SDK and am currently facing some configuration issues with the MAX30101 driver in a Zephyr project. Here is the example program and source...
Mac with M1 silicon, installed latest Mac-specific nRF Connect for Desktop (5.02) and latest command line tools: 10.24.2 macOS
DLL error in GUI app:
Command line fails...
HI
when I try to uninstall/remove my connect sdk, tool chain manager says:
Failed to remove C:\nordicsemi\v2.6.0, operation not permitted. Please close any application...
Hi I have been working on an project using nrf5sdk_17_1_0 using Segger 5.42a but when I try to build the Blinky example it gives me build failed without any syntax error
We are developing a sleepy end device using the nRF52840, based on the light switch sample. We have set zb_set_ed_timeout to 16384 minutes, which is approximately 11 days...
Hello,
I am using the NRF52832 in my PCB design, and I have attached a screenshot of relevant part of the layout. My PCB manufacturer pointed out that some vias overlap...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi,
Since we started testing the new nRF9151 with the latest modem firmware (v2.0.1), we’ve noticed a change in GNSS behavior compared to the nRF9161/v1.3.6.
Recently...
Hi there!
We're trying to port the FreeRTOS Cellular Interface to work with the nRF9160 which is running the Serial LTE Modem application. The problem we are facing is a...
i have a nrf52840dk that is flashed with a old program i used. i want to try the nfc tag and read it using my phone. what should i flash to my nrf52840dk in order to use it...
Hello,
I am building the existing WIFI station app for the Thingy53 with the nRF 7002EB board - sample code: nrf/samples/wifi/sta
In the CMakeLists.txt file, the line...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
