Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
In the new AzureIotHub library, subsys\net\lib\azure_iot_hub\src\azure_iot_hub.c
the logic for handling connection conditions in mqtt_evt_handler requires more error...
How is CRYPTOCELL_IRQHandler linked in a project using CC310? I have built ble_app_interactive and it links to the library routine. However I need to develop my own application...
The current state of my thingy 91 is it blinks blue and then red. nrf connect reports that it has not been provisionized or something similar.
The included sim card is registered...
This is the third time attempting to install nRF Connect SDK on my Linux box at home, and have failed at the same place every time. I followed all the instructions while using...
Dear Support Team,
We are migrating our designs to nRF52820. With previous IC we saw that Johanson has IPD for atenna filter + matching circuit (e.g.2450FM07A0029), but...
Now we have a new project,in order to long distance communication,we add a PA RFX2411N in our design,now how may I tuning the pi (or T) match network between nRF52 chip and...
Hi All, What is the best way to modify ble_app_multilink_central and ble_app_blinky example codes, so BLE tag can send to ble_app_multilink_central Its own address. The ble_multilink...
My application uses a NRF52 (SD132, SDK 15.0.0), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
Hi, I'm having some issues with migrating from SDK12.1 to SDK16 while discovering services.
It seems to connect to Android without much issue, but on iOS the connection...
A project is currently utilizing an NXP module to access the SD card via 4-bit SDIO. I am exploring the feasibility of integrating an nRF52840-based module, and have a few...
I am trying to use the battery example in " /ncs/zephyr/samples/boards/nrf/battery" to measure my 3V coin cell via VDD. I am using P0.14 to enable a set load on VDD before...
I'm using a nRF52840 DK (PCA10056 2.0.1 2020,14 683193023) with an adafruit FTDI serial TTL-232 USB cable (part number P70C uses the FTDI -FT232R chip inside a translucent...
i use pca20023-sr3_nrf52832_product_example demo to test, but there was an error occued , the segger rtt views displays:
00> [00000000] <info> app: System ON 00> [00000000...
Hello,
I'm in the process of developing the HW board for a nRF5340-based product. I need the customer could update the firmware using a serial port (USB or Bluetooth is...
